Zaxis - Customer testimonials - Send us your comments and pictures!

I bought a Zaxis for my parents for Christmas. Installed it in about 30 minutes. They have an older NuWa, and so it was pretty easy.

My wife asked me if I bought one for us and I said "no, but maybe later". Well, between my friend Ozz and my devious wife, I got one for Christmas, too! She asked Ozz to get one, have it delivered to their place (so I wouldn't know!), and surprised me on the big day!

It took me about 45 minutes to install in our 3400, only because I wanted to wrap the wires in loom and wanted to place it towards the front of the front compartment so that I could easily get to the on/off switch.

I LOVE IT!!!!

And, to echo previous posts about quality, it is a well thought out and engineered unit. Simple connections, and it WORKS!

Since we have a BedSaver, I have had to (in the past...) raise the kingpin above the BedSaver, back up a little bit, then lower the 5er to the right hookup position. Now, I don't have to get out of the truck!!!!

I can tell you this: for a buck and a half, it is one option worth getting. My dad would never have bought it because he is watching his pennies. But, after installing it, he was jazzed, and my mom could see applications too: in the past she would tell dad to raise or lower so that the fridge would work (remember I told you they have an older NuWa) and she would either have to shout or go out and in to look at the level on their counter. She too, is jazzed.

Maybe I should get a patronage fee for this commercial. Oh well...

Michael

...It wasn't hard at all to install. Paul being an electrician was able to pop it all together in no time at all. Even if you aren't an electrician the instructions are very clear. We haven't had any problems at all in fact it has done away with all of the problems that we were having, the screaming, name calling, cussing, spitting, sputtering, and whatever else goes on when 2 people work against each other. No matter what I would say, he wouldn't believe me and would second guess me which always made for a lovely day. This way I felt there was no one to blame except the one with the remote... LOL. Really, it is a delight having this remote system...

Regards Kathi

Here are some photos of the Zaxis install in our 2005 Wildcat 29BHBP. The installation was very easy, the toughest part was to find the mounting location. I also used this opportunity to re-route and protect some of the original wiring that should have been done at the factory. This is a very convenient and easy to use product. Thanks.

Regards,
Mike

I just wanted to let you know that after several trips with the Zaxis unit installed on our Montana 2980RL that I am very pleased with the product. Having the remote makes hooking up so much easier and quicker as I can be raising or lowering the landing gear while walking around and checking other things. My wife is amazed at how easy it is to be able to control the kingpin height from the cab of the truck while hooking up. Thanks again for a great product.

Bill & Shari Hill

We just completed the install of the Zaxis Landing Gear Remote on our Wildcat. It's a very nice system that we couldn't live without after trying it.

Travis

Installation went smoothly and it worked first time. I installed the Zaxis on the front basement wall near the left side access door. This required drilling a pass-through hole in the basement wall to run the wires to the front compartment where the jack motor and rocker switch are located. Have used it for several outings already and find it to be a great convenience! Hitching and unhitching can now be done from inside the cab or for just leveling after unhitching, in the shade of a nearby tree. In fact, I now prefer using the key fob to the rocker switch.

Great product! Thanks!

Dave & Lori

Thank you for the prompt shipment. I installed it yesterday, and if worked right off the bat. The installation was pretty simple, but I did have an electrician friend with me to help as I didn't want to screw up the installation. Attached is a picture of my installation. It went in on the opposite side from the motor but right next to the landing gear switch. There was plenty of extra wire at the switch so we only used about 8" of new wire. Very clean installation and took one hour, but admittedly it could have taken less time because we spent most of the hour looking at the wiring diagram and the trailer wiring. Next week we take off on the road for a 3 week trip so it will get a good work out. Thanks again.

Jeff

Here are 3 photos from the Zaxis install on our 2005 Montana model 3500RL. Not a difficult install at all. Deciding where to cut the battery to switch wires was probably the most difficult part. Total install time was probably 30 to 45 minutes.

Works great!!

Dickie

I wanted to update you on my Zaxis install project. Everything worked as planned. Very easy install. Even the installation of the second switch to allow me to control the front landing gear as well as the rear electric stabilizer jacks. Great product.

P.S. Looks like Harry from Factoryville, PA must have read my post about the second switch install on the Cedar Creek RV Club forum (http://CedarCreekRVClub.com/).

Sincerely,
Darrell and Jean

I installed the Zaxis with no problems. The most time was spent installing the unit it self as to the confined space I had to work in. The landing gear and the rear stabilizers all work from the unit. I installed a DPDT switch (NAPA part no TG6144.) This way the landing gear and stabilizers can be operated from the remote control unit by switching to what I want working.

Harry

This is the finished installation showing the DPDT switch and part of the Zaxis unit. I have to tell you this is a fine piece of equipment and it works great with the landing gear and the rear stabilizers. I wish you great success with the unit and will sure show it to all my camping friends.

Harry

Just a note to let you know my wife really likes the Zaxis. Before I installed the Zaxis I would backup to the hitch and the wife would raise or lower the coach until the right height was reached. Now I do it from inside the truck with the remote while the wife is visiting with friends.

Thanks for all your help and for staying in touch to make sure all worked for me.

The Zaxis works great!

Wayne

The Zaxis Landing Gear Remote Control unit you sent was received yesterday and I installed it this morning. It works fine and the installation was a breeze.

Choosing a location with convenient access seemed to be the largest criteria to the installation, I put mine on the inside of the lower front wall next to the back side of the manual switch. I've used the Zaxis while hitching and unhitching several times and have found it makes the process much easier and convenient. It eliminates climbing in and out of the cab to make small height adjustments with the manual switch.

Regards,
Richard

That had to be 1 of the easiest installs out there. This is a KZ Sportster 37p2 all the wires had #10 wire nuts so all I needed to do was make a wire harness to the receiver, wire tie it and make it look good. Start to finish 30 minutes tops and that included taking the LP tanks out.

Fred

Here are a few pictures. It is on a 2003 HR Presidential 36SKT fiver. I got the matching AMP connectors from an electronics web store that helped make it a cleaner install. Please excuse the battery setup. It is temporary for the winter as I will be taking them out soon. This unit was not setup for multiple batteries so I am figuring a way to do it right.

I hope to see your system written up in Trailer Life magazine. Any chances of that?

Vince


Online Security•Privacy Policy•Terms of Use	COPYRIGHT © 1999-2010 WESTHAVER ASSOCIATES, INC.